We've noticed this post involving What Would Cause My Electric Water Heater to Stop Working? below on the net and felt it made good sense to relate it with you on this site.
Several contemporary residences use an electric hot water heater for their heating system, because of its convenience and also ease of use. Nonetheless, just like any other electric appliances, issues may develop with its use, suddenly. It can be actually aggravating to awaken to a cold shower as opposed to a hot one or having your bathroom with water that isn't warm sufficient or perhaps too warm. Whatever the instance may be, hot water heater problems can be rather aggravating. Thankfully, we have actually made a list of possible remedies to your hot water heater concerns. There are a variety of elements that could trigger most of these issues, maybe an issue with the power supply, the electric heating element, or the thermostat. Prior to doing anything, guarantee you turn off the primary power supply for safety and security. Whatever the problem is, getting it repaired must not posture too much of a problem if you comply with these actions:
Call A Specialist:
If after replacing all defective components and also resetting your temperature, the water heater still isn't functioning, you might require to speak to an expert plumber for a professional viewpoint. The issue with your heating system could be that the cold and hot taps have been changed or it might be undersized for the quantity of warm water required in your home. Whatever the case may be, an expert plumber would certainly aid address the problem.
Check Your Power Supply:
As fundamental as this may appear, it is really essential. Without appropriate power, your hot water heater will certainly not operate. So the first thing to do when your water suddenly stops working is to confirm that it isn't a power problem. Check if the fuse is blown out or the circuit breaker tripped. If the circuit breaker is the problem, just turn it off and on again. Replace any broken or worn-out fuse. Test the appliance with power after these changes to see if it's now working.
Check Your Thermostat:
If your water heater still isn't working or the water coming out isn't warm sufficient, you might require to examine the temperature level setups on your top thermostat. Make sure the breaker is switched off before doing anything. Open the access panel and press the red button for temperature reset above the thermostat. This ought to help heat the water. Turn the breaker back on and also examine if the issue has been fixed.
Check the Heating Element in the Water Heater:
If it's not a power trouble, then try checking out your burner if it is still functioning. Check each of your heating elements to be sure the problem isn't with any one of them. If any one of them is malfunctioning, replace that part and afterwards inspect whether the warm water is back on.
Final thought
Water heater problems are not constantly significant. A lot of them are due to small problems like a blown fuse or worn-out heating element. Changing the malfunctioning parts need to suffice. Nevertheless, if you are still unable to address the issue, give a call to your closest plumber to come to get it dealt with.
What Would Cause My Electric Water Heater to Stop Working?
Your water heater is one of the most forgotten-about appliances in your home—until it quits working. Once you realize that there’s no hot water, the water heater jumps up to become the most noticeable appliance you have. No one in your family will be happy until you get the water heater fixed.
To fix an electric water heater as soon as possible, follow the troubleshooting advice discussed below.
Basic Water Heater Troubleshooting
Fortunately, you may be restore the hot water supply simply by resetting the house circuit breaker for the water heater. A tripped circuit breaker is one of the top causes of water heater failures. Shut the hot water heater breaker off then turn it back on. Give the water heater a half hour to heat up (if it’s working) and then check for hot water through one of your faucets.
If you get hot water after resetting the breaker, then the problem may be fixed if the breaker inadvertently tripped and it doesn’t continue tripping.
If the water heater breaker trips again, then you’ll likely need to have a service technician examine and repair the water heater. The service technician will check the circuit breaker and electrical supply wiring for the water heater. A short in the supply wiring or a bad circuit breaker could be causing the breaker to trip. An internal failure such as a broken heating element can also cause the breaker to continue tripping.
When resetting the water heater circuit breaker doesn’t work at all, then the water heater may be getting power while an internal water heater failure is causing the problem.
Conduct Advanced DIY Water Heater Troubleshooting
If the water heater doesn’t work after resetting the high-temperature limit switch, then you’ll need to either conduct some advanced water heater troubleshooting or have a service technician diagnose and repair the water heater failure.
Sears Technicians created a safe and highly-successful DIY advanced troubleshooting video to help you determine the cause of a water heating failure if you want to try to fix the problem yourself. Follow the advice in this video to find and fix the cause of the heating failure on your own:
The video begins with the basic troubleshooting described in the first 2 sections described above. It then goes on to guide you through checking water heater components to safely find the cause of the water heating failure.
If you get to a point in the troubleshooting where you’re not completely confident that you can safely continue, schedule a service technician to diagnose and repair the water heater.
The DIY water heater troubleshooting shown in the above video differs from the diagnosis techniques that service technicians typically use when examining a water heater to find the cause of a heating failure. Safe DIY troubleshooting doesn’t rely on live voltage checks while service technicians often use live voltage checks to quickly find the cause of water heater failures.
While many DIY’ers have been able to find the cause of water heater failures using troubleshooting advice shown in the video, some failures such as a bad circuit breaker can only be found using live voltage checks which should only be conducted by a trained service technician.
Sears Technicians have the training, tools and expertise to quickly find the cause of a water heater failure. Rely on our technicians to diagnose and repair your water heater or any other appliance in your home that quits working.
While the technician is in your home, take advantage of appliance Cleaning & Maintenance offers that the tech discusses with you. Keeping your appliances well-maintained will help them work more efficiently and last longer. Regular professional maintenance will also help prevent costly breakdowns of the appliances you depend on every day.
https://www.searshomeservices.com/blog/what-would-cause-my-electric-water-heater-to-stop-working
I ran across that piece about What Would Cause My Electric Water Heater to Stop Working? when doing a lookup on the internet. So long as you enjoyed our blog post please don't forget to pass it around. I treasure reading our article about What Would Cause My Electric Water Heater to Stop Working?.
Information Here